Additional Information Part Number HTL05-D-4Q-L Specifications Enclosure Chassis Input Voltage 115 / 230 VAC Output Voltage 0 - 12, 0 - 24 VDC Continuous Current 5 Amps Peak Current 7.5 Amps (10 Seconds) Braking Type Regenerative Reversing Type Regenerative Isolation 0-5 VDC

Additional Information Part Number HTL1.5-D-4Q Features Microprocessor based Custom programming available for OEMs. Isolation Easy interface to a PLC and added safety. Four Quadrant Reverse and/or brake on the fly. Actuator Control The standard HTL drive can be used with actuators. There is also...

Additional Information Part Number HTL10-D-4Q Features All-in-One Package Combines a custom regen-capable switching power supply with low voltage drive Dynamic Brake Output Built-in circuitry to divert regenerative current to dump resistor for quicker braking than most PWM drives Alarm Output N.O. and N.C. contacts...

Additional Information Part Number LV01-24AC-E10U Features 16kHz switching frequency A high switching frequency means a quiet motor! Spade terminals Easy to use, lower cost and able to fit in a smaller package. Speed range and regulation 1% speed regulation over 100:1 speed range. User...

Additional Information Part Number LV02-24AC Features Additional features AC or DC input choices and near unity form factor throughout the speed range. Low voltage motor operation Designed for 12 and 24VDC motors. Spade terminals Easy to use, lower cost and able to fit in...

Additional Information Part Number LV02-24DC Features 16kHz switching frequency A high switching frequency means a quiet motor! Speed range and regulation 1% speed regulation over 100:1 speed range. Stopping modes Decelerate to a stop by adding a N.O. switch to the pot circuit or...

Additional Information Part Number M1 Features Stopping Modes Inhibit (N.O.) for coasting to a stop. Can be used for frequent starting and stopping Microprocessor Based Allows custom programming for OEMs Deceleration Current Limit 1.37 Form Factor 1% Base Speed Regulation 601 Speed Range Maximum Speed Minimum...

Additional Information Part Number M2 Features Stopping Modes Inhibit (N.O.) for coasting to a stop. Can be used for frequent starting and stopping 1.37 Form Factor 1% Base Speed Regulation Current Limit (A & B) IR Compensation (A & B) Torque Mode Can be used...

Additional Information Part Number M2-D Features Microprocessor Based Allows custom programming for OEMs Minimum Speed (A & B) Accel / Decel (A & B) Two Motor Outputs Two separate motor outputs Two Operating Modes The motors can be run independently or in a ratio...

Additional Information Part Number MC10 Features Pre-Wired Switches ON/OFF NEMA 4X Plastic Enclosure Plastic corrosion resistant weatherproof enclosure that protects against dirt and splashing Stopping Modes Inhibit (N.O) for coasting to a stop. Can be used for frequent starting and stopping Minimum Speed Acceleration Deceleration...

Additional Information Part Number MC10-PCM Features Stopping Modes Inhibit (N.O) for coasting to a stop. Can be used for frequent starting and stopping 601 Speed Range Maximum Speed Isolated Logic Allows floating or grounded 0 - 10 VDC or 4 - 20 mA signals Minimum...

Additional Information Part Number MC10-R Features Deceleration Current Limit NEMA 4X Plastic Enclosure Plastic corrosion resistant weatherproof enclosure that protects against dirt and splashing Field Supply Voltage output to energize the field winding of a shunt-wound motor Reversing Reversing switch swaps armature leads to...

Additional Information Part Number MDBL03-D230-PCM Features Doubler mode Can double a 115 VAC line to a 280 VDC bus output. Maximum Speed Acceleration Thermally protected Drive recognizes when overheated as a result of overload. It first flashes a warning code on the status LED...

Additional Information Part Number MDBL05-D230-PCM Features Thermally protected Drive recognizes when overheated as a result of overload. It first flashes a warning code on the status LED and will eventually trip if the condition persists. Doubler mode Can double a 115 VAC line to...

Additional Information Part Number MDPM03-D230-4Q-PCM Features 1.05 Form Factor 1% Base Speed Regulation Isolated inputs Accepts floating or grounded signals 0 ± 5 VDC, 0 ± 10 VDC or 4-20 mA. Thermally protects Drive recognizes when overheated as a result of overload. It first...

Additional Information Part Number MDPM07-D230-4Q-PCM Features 1001 Speed Range Zero Adjust Dump circuitry Internal circuitry for the hookup of an external dump resistor. Doubler mode Can double a 115 VAC line to run a 180 VDC motor. Minimum Speed Maximum Forward Speed Thermally protects...

Additional Information Part Number MDVF03-D230-PCM Features Control a variety of motors 3-phase induction motors, single-phase permanent split capacitor (PSC), shaded pole, and synchronous motors. Stopping modes User can use DC Injection braking, decelerate, or coast the motor to a stop. Thermally protects Drive recognizes...

Additional Information Part Number MDVF05-D230-PCM Features Acceleration Deceleration Control a variety of motors 3-phase induction motors, single-phase permanent split capacitor (PSC), shaded pole, and synchronous motors. Quadrature encoder option For OEM applications, the drive can be programmed to follow quadrature encoder feedback without any...

Additional Information Part Number MGB400-1.5-00MD Features Offset Current Limit MM Footprint Traditional MM mounting pattern and footprint Microprocessor Based Allows custom programming for OEMs 1.37 Form Factor 1% Base Speed Regulation 501 Speed Range Maximum Speed 4Q Reversing Regenerative / 4-Quadrant drives have the...

Additional Information Part Number MGB400-11-00MD Features Torque Mode Can be used for speed control or torque control for tension applications Configurable Stop Switch Can be configured to be either normally open or normally closed, and to coast or regeneratively brake. Diagnostic LEDs Current Limit,...

Additional Information Part Number MGC403-11-00MD Features Cycling with Limit Switches Cycling with Feedback Allows for quicker wiring and setup Diagnostic LEDs: 1% Base Speed Regulation 60:1 Speed Range 8 Modes of Operation Speed Independent Speed & Torque Cycling with Current Limit Positioning Field Supply:...

Additional Information Part Number MM03-115AC-PCM Features Deceleration Current Limit Minimum Speed Acceleration Diagnostic LEDs Current Limit, Inhibit, Power, Run 1.37 Form Factor 2% Base Speed Regulation Stopping Modes Inhibit (N.O. or N.C.) for coasting to a stop. Can be used for frequent starting and...

Additional Information Part Number MM03-230AC-PCM Features Minimum Speed Acceleration 601 Speed Range Maximum Speed Stopping Modes Inhibit (N.O. or N.C.) for coasting to a stop. Can be used for frequent starting and stopping Diagnostic LEDs Current Limit, Inhibit, Power, Run On-board Fuses Drive includes...

Additional Information Part Number MM10-115AC-PCM Features 601 Speed Range Maximum Speed Stopping Modes Inhibit (N.O. or N.C.) for coasting to a stop. Can be used for frequent starting and stopping On-board Fuses Drive includes an on-board fuse Field Supply Voltage output to energize the...

Additional Information Part Number MM10-230AC-PCM Features Field Supply Voltage output to energize the field winding of a shunt-wound motor Minimum Speed Acceleration Deceleration Current Limit 601 Speed Range Maximum Speed Stopping Modes Inhibit (N.O. or N.C.) for coasting to a stop. Can be used...