WEIDMULLER 8975590000

Additional Information

Part Number

8975590000

General Data

Accuracy

0.5 % FSR

Configuration

DIP switch

Galvanic isolation

2-way isolator

Input/Output

1 /5/ 10 A AC / 4...20 mA (current loop)

Rail

TS 35

Step response time

typ. 700 ms

Temperature coefficient

‰¤ 200 ppm/K

Voltage supply

13...30 V DC, via output current loop

Approvals

Approvals

CE, CULUSEX, EAC

ROHS

Conform

Dimensions And Weights

Length

72 mm

Length (inches)

2.835 inch

Width

22.5 mm

Width (inches)

0.886 inch

Depth

112.4 mm

Depth (inches)

4.425 inch

Weight

150 g

Net weight

101 g

Connection Data

Type of connection

Screw connection

Clamping range, rated connection

2.5 mm²

Clamping range, min.

0.5 mm²

Clamping range, max.

2.5 mm²

Tender Specification Sheets

Long specification

Monitoring component for AC currents up to 10A with 4...20 mAloop feed and electrical isolationCurrent monitoring component in 22.5 mm width for recording 50/ 60 HzAC currents 0...1 A / 0...5 A / 0...10 A. Input range can be selected using DIP switches.Power is fed to the component via the 4...20 mA current loop on the output side.The input and output circuits have 6 kV of electrical isolation.Approved for ATEX Zone2 and UL C1 D2 applications.Add-on housing for TS35 rail mountingDimensions: L/W/H 72/ 22.5/ 92.4 mmScrew connection / Nominal cross-section 2.5 mm2Protection degree: IP 20   Input                         0...1 A / 0...5 A / 0...10 A AC switchable                                      50 / 60 HzVoltage of measuring circuit 250 V ACOutput                                             4...20 mA current loopLoad resistance            < 600 Ohm Strom>1 kOhm / voltageTransmission error               < 0,5% v. E. Temperature coefficient 200 ppm / KStep response time typ. 700 msAuxiliary power                                     via output-side current loopAmbient temperature range 0°C...+50°C Secure isolation                   EN 50178, 2-way isolation up to 6 kVTest voltage                               4 kV input against outputRated voltage                                         300 V AC/DC at overvoltage category III and pollution degree 2Approvals cULus, cULusEX C1D2, ATEX Zone 2Type                                                            WAS1 CMA LP 1/5/10A EX

Short specification

Monitoring component for AC currents up to 10A with 4...20 mAloop feed and electrical isolationCurrent monitoring component in 22.5 mm width for recording 50/ 60 HzAC currents 0...1 A / 0...5 A / 0...10 A. Input range can be selected using DIP switches.Power is fed to the component via the 4...20 mA current loop on the output side.The input and output circuits have 6 kV of electrical isolation.Approved for ATEX Zone2 and UL C1 D2 applications.

Input

Number of inputs

1

Input current

0...1 A AC/ 0...5 A AC/ 0...10 A AC

Input frequency

50...60Hz

Classifications

ETIM 6.0

EC002653

ETIM 7.0

EC002653

EClass 9.0

27-21-01-20

EClass 9.1

27-21-01-20

EClass 10.0

27-21-01-20

Output

Number of outputs

1

Output signal limit

Approx. 24 mA

Output current

4...20 mA (current loop)

Load impedance current

‰¤ 600 ©

Offset current

max. 100 µA

Status indicator

LED ON: OK; LED flashing: signal out of range;LED OFF: Error

Product Information

Product information

This product will soon be replaced by a new product.Please do not use with new systems. Please contact our technical support.

Environmental Product Compliance

REACH SVHC

Lead 7439-92-1

Insulation Coordination

Clearance & creepage distances

‰¥ 5.5 mm

EMC standards

EN 55011, EN 61000-6

Galvanic isolation

2-way isolator

Impulse withstand voltage

6 kV

Insulation voltage

4 kVeff / 5 s

Pollution severity

2

Rated voltage

300 V

Surge voltage category

III

Temperatures

Operating temperature, max.

50 °C

Operating temperature, min.

0 °C

Storage temperature, max.

70 °C

Storage temperature, min.

-20 °C

Operating temperature

0°C...50°C

Storage temperature

-20°C...70°C