WEIDMULLER 2456070000

Additional Information

Part Number

2456070000

Probability Of Failure

MTBF

215 Years

SIL PAPER

SIL certificate

Digital Output

Type

NPN-Transitor, Switching frequency 5 kHz

Nominal switching voltage

30 V DC

Continuous current

80 mA

Function

Output = input, direct or inverse (configurable)

Approvals

Approvals

DNV GL, EAC

ROHS

Conform

Dimensions And Weights

Width

22.5 mm

Width (inches)

0.886 inch

Height

127.3 mm

Height (inches)

5.012 inch

Depth

114.6 mm

Depth (inches)

4.512 inch

Net weight

170 g

Safety-Related Specifications Low Demand Mode

Average Probability of Failure on Demand (PFD

1.58 x 10-4 (Tproof = 1 year), 3.17 x 10-4 (Tproof = 2 years), 7.92 x 10-4 (Tproof = 5 years)

Connection Data

Type of connection

PUSH IN

Wire connection cross section AWG, min.

AWG 26

Wire connection cross section AWG, max.

AWG 14

Wire cross-section, solid, min.

0.2 mm²

Wire cross-section, solid, max.

2.5 mm²

Wire connection cross-section, finely stranded, min.

0.2 mm²

Wire connection cross section, finely stranded, max.

2.5 mm²

Wire connection cross-section, finely stranded with wire-end ferrules DIN 46228/4, min.

0.2 mm²

Wire connection cross-section, finely stranded with wire-end ferrules DIN 46228/4, max.

2.5 mm²

Rated Data Ul

UL certificate

E337701.pdf

Safety-Related Basic Specifications

Demand mode

High

Demand rate

1,000 s

Description of the "safe state"

High impedance

Device type

B

Diagnostic test interval

10 s

Hardware fault tolerance (HFT)

0

Mean Time To Repair (MTTR)

8 h

Safe Failure Fraction (SFF)

92 %

T

5 Years

Total failure rate for dangerous detected failures (»

135 FIT

Total failure rate for dangerous undetected failures (»

36 FIT

Total failure rate for safe detected failures (»

0 FIT

Total failure rate for safe undetected failures (»

275 FIT

Safety category

SIL 2

Probability of outage PFH

3.62 x 10-8 h-1

Alarm Output

Alarm function

Line interruption at the input, Short circuit at input, No supply voltage, Device error

Type

Relay, 1 NC (voltage-free)

Nominal switching voltage

‰¤ 125 V AC / 110 V DC (safe area)‰¤ 32 V AC / 32 V DC (zone 2)

Continuous current

‰¤ 0.5 A AC / 0.3 A DC (safe zone), ‰¤ 0,5 A AC / 1 A DC (zone 2)

Power rating

‰¤ 62.5 VA / 32 W (safe area)‰¤ 16 VA / 32 W (Zone 2)

Classifications

ETIM 6.0

EC002653

ETIM 7.0

EC002653

EClass 9.0

27-21-01-20

EClass 9.1

27-21-01-20

EClass 10.0

27-21-01-20

Output

Influence of load resistance

‰¤ 0.01% of span / 100 ©

Environmental Product Compliance

REACH SVHC

Lead 7439-92-1

Data For Ex Applications (Atex)

Voltage U

10.6 V DC

Current I

12 mA DC

Power P

32 mW

Marking

II (1) G [Ex ia Ga] IIC/IIB/IIA, II (1) D [Ex ia Da] IIIC, I (M1) [Ex ia Ma] I

Installation location

Device installed in safe area, zone 2

Insulation Coordination

EMC standards

DIN EN 61326, NE 21

Insulation voltage

2.6 kV (input / output)

Rated voltage

300 V

Input Ex

Input frequency

0...5 kHz

Input resistance

1 k©

Output signal in case of wire break

< 0.1 mA, > 6.5 mA (in case of wire break)

Pulse duration

> 0.1 ms

Resistance

Series resistor 750©, Parallel resistor 15k©

Sensor

NAMUR sensor, according to EN60947, switch with or without RS, RP

Sensor supply

8 V DC / 8 mA

Trigger level high

> 2.1 mA

Trigger level low

< 1.2 mA

Type

intrinsically safe circuit

Temperatures

Humidity

0...95 % (no condensation)

Operating temperature, max.

60 °C

Operating temperature, min.

-20 °C

Storage temperature, max.

85 °C

Storage temperature, min.

-20 °C

Operating temperature

-20 °C...60 °C

Storage temperature

-20 °C...85 °C

Ratings Iecex/Atex/Cul

ATEX certificate

09ATEX0168X.pdf

IEC Ex certificate

IECEx certification

General Specifications

Configuration

With FDT/DTM software

Voltage supply

19.2€¦31.2 V DC

Type of connection

PUSH IN

NAMUR supply

8 V DC / 8 mA

Power consumption

‰¤ 1.1 W

Protection degree

IP20

Humidity

0...95 % (no condensation)